This gives small but noticeable rx performance improvement (2-3%)
and will allow exploiting future napi improvement.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The recent change in HD-audio HDMI/DP codec driver for allowing the
dynamic PCM binding introduced a new spec->pcm_mutex. One of the
protected area by this mutex is hdmi_present_sense(). As reported by
Intel CI tests, unfortunately, the new mutex causes a deadlock when
the hotplug/unplug is triggered during the codec is in runtime
suspend. The buggy code path is like the following:
hdmi_unsol_event() -> ...
-> hdmi_present_sense()
==> ** here taking pcm_mutex
-> hdmi_present_sense_via_verbs()
-> snd_hda_power_up_pm() -> ... (runtime resume calls)
-> generic_hdmi_resume()
-> hdmi_present_sense()
==> ** here taking pcm_mutex again!
As we can see here, the problem is that the mutex is taken before
snd_hda_power_up_pm() call that triggers the runtime resume. That is,
the obvious solution is to move the power up/down call outside the
mutex; it is exactly what this patch provides.
The patch also clarifies why this bug wasn't caught beforehand. We
used to have the i915 audio component for hotplug for all Intel chips,
and in that code path, there is no power up required but the
information is taken directly from the graphics side. However, we
recently switched back to the old method for some old Intel chips due
to regressions, and now the deadlock issue is surfaced.
Fixes: a76056f2e5 ('ALSA: hda - hdmi dynamically bind PCM to pin when monitor hotplug')
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If mmc_blk_ioctl returns -EINVAL, blkdev_ioctl continues to
work without returning err to user-space. But now we check
CAP_SYS_RAWIO firstly, so we return -EPERM to blkdev_ioctl,
which make blkdev_ioctl return -EPERM to user-space directly.
So this will break all the ioctl with BLKROSET. Now we find
Android-adb suffer it for the following log:
remount of /system failed;
couldn't make block device writable: Operation not permitted
openat(AT_FDCWD, "/dev/block/platform/ff420000.dwmmc/by-name/system", O_RDONLY) = 3
ioctl(3, BLKROSET, 0) = -1 EPERM (Operation not permitted)
Fixes: a5f5774c55 ("mmc: block: Add new ioctl to send multi commands")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using an at91sam9g20ek development board with DTS configuration may trigger
a kernel panic because of a NULL pointer dereference exception, while
configuring DMA. Let's fix this by adding a check for pdata before
dereferencing it.
Signed-off-by: Brent Taylor <motobud@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When initializing sdio card, we get struct mmc_card
from mmc_alloc_card which allocates it by kzalloc. So we
don't need another memset while reading cccr.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When initializing sd or sdio card, we get struct mmc_card
from mmc_alloc_card which allocates it by kzalloc. So we don't
need another memset while decoding cid.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/of_mmc_spi.c: In function 'mmc_spi_get_pdata':
drivers/mmc/host/of_mmc_spi.c:77:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret = -EINVAL;
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds Generic PHY access for sdhci-of-arasan. Driver
can get PHY handler from dt-binding, and power-on/init the PHY.
Currently, it's just mandatory for arasan,sdhci-5.1.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, some err handling of sdhci_arasan_probe return directly
without calling sdhci_pltfm_free. This patch fixes them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't really need disable clk_ahb when failing to resume. Otherwise
we may take risk of bus error for accessing register without clk_ahb.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds phys and phy-names for sdhci-of-arasan as required
properties for arasan,sdhci-5.1, and details the example as well.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Normally the timeout clock frequency is read from the capabilities
register. It is also possible to set the value prior to calling
sdhci_add_host() in which case that value will override the
capabilities register value. However that was being done after
calculating max_busy_timeout so that max_busy_timeout was being
calculated using the wrong value of timeout_clk.
Fix that by moving the override before max_busy_timeout is
calculated.
The result is that the max_busy_timeout and max_discard
increase for BSW devices so that, for example, the time for
mkfs.ext4 on a 64GB eMMC drops from about 1 minute 40 seconds
to about 20 seconds.
Note, in the future, the capabilities setting will be tidied up
and this override won't be used anymore. However this fix is
needed for stable.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The header file asm/sizes.h is unnecessary, let's remove it.
This also allows to compile under X86 arch.
Signed-off-by: Wang Hongcheng <annie.wang@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds the HIDs for Qualcomm Technologies Inc SDHC
controllers:
QCOM8051: non-removable device that does not support 1.8v
QCOM8052: non-removable device that does support 1.8v
Signed-off-by: Philip Elcan <pelcan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Tegra30+ SDMMC module has memcomp pads that are used to
automatically find and set the correct drive strength settings to
the sdmmc pads. The calibration needs to be manually kicked off
when the card signal voltage is changed, after the card clock is
supplied again.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased to fix a trivial compile error]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've introduced a new helper in the MMC core:
mmc_regulator_set_vqmmc(). Let's use this in mtk-sd. Using this new
helper has some advantages:
1. We get the mmc_regulator_set_vqmmc() behavior of trying to match
VQMMC and VMMC when the signal voltage is 3.3V. This ensures max
compatibility.
2. We get rid of a few more warnings when probing unsupported
voltages.
3. We get rid of some non-mediatek specific code in mtk-sd.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit ceae98f20e ("mmc: core: Try other signal levels
during power up") we can see that there are times when it's
valid to try several signal voltages. Don't print an ugly
error in the logs when that happens.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The new code to do the clock rate setting externally to the SDMMC
module has a shortcut to not propagate changes with a 0 rate to
the CAR by simply bailing out. This breaks proper cutting of the
card clock. Fix it by directly calling the correct sdhci function.
Fixes: a8e326a911 "mmc: tegra: implement module external clock change"
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In control compatibility layer, when no elements are found by
ELEM_READ/ELEM_WRITE ioctl commands, ENXIO is returned. On the other hand,
in core implementation, ENOENT is returned. This is not good for
ALSA ctl applications.
This commit changes the return value from the compatibility layer so
that the same value is returned.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit e34d65696d ("stmmac: create of compatible mdio bus for stmmac
driver") broke DW GMAC functionality on ARC AXS10x boards:
That's what happens on eth0 up:
--------------------------->8------------------------
| libphy: PHY stmmac-0:ffffffff not found
| eth0: Could not attach to PHY
| stmmac_open: Cannot attach to PHY (error: -19)
--------------------------->8------------------------
Simplest solution is to add PHY description in board's .dts.
And so we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Phil Reid <preid@electromag.com.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 4.5
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Use helper of_platform_default_populate() in linux/of_platform
when possible, instead of calling of_platform_populate() with
the default match table.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
linux-next for 4.6-rc1 timeline reported ARC build failures !THP
| arch/arc/include/asm/tlbflush.h:29:0: warning: "flush_pmd_tlb_range" redefined [enabled by default]
| arch/arc/include/asm/tlbflush.h:29:0: warning: "flush_pmd_tlb_range" redefined [enabled by default]
| arch/arc/include/asm/tlbflush.h:29:0: warning: "flush_pmd_tlb_range" redefined [enabled by default]
Turns out that commit ("mm/thp/migration: switch from flush_tlb_range
to flush_pmd_tlb_range") triggered the issue while the problem was in
ARC code where THP specific helpers were not guarded with #ifdef.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Remove the livepatch module notifier in favor of directly enabling and
disabling patches to modules in the module loader. Hard-coding the
function calls ensures that ftrace_module_enable() is run before
klp_module_coming() during module load, and that klp_module_going() is
run before ftrace_release_mod() during module unload. This way, ftrace
and livepatch code is run in the correct order during the module
load/unload sequence without dependence on the module notifier call chain.
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Put all actions in complete_formation() that are performed after
module->state is set to MODULE_STATE_COMING into a separate function
prepare_coming_module(). This split prepares for the removal of the
livepatch module notifiers in favor of hard-coding function calls to
klp_module_{coming,going} in the module loader.
The complete_formation -> prepare_coming_module split will also make error
handling easier since we can jump to the appropriate error label to do any
module GOING cleanup after all the COMING-actions have completed.
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tPgH
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Added support for some new video formats
- mn88473 DVB frontend driver got promoted from staging
- several improvements at the VSP1 driver
- several cleanups and improvements at the Media Controller
- added Media Controller support to snd-usb-audio. Currently, enabled
only for au0828-based V4L2/DVB boards
- Several improvements at nuvoton-cir: it now supports wake up codes
- Add media controller support to em28xx and saa7134 drivers
- coda driver now accepts NXP distributed firmware files
- Some legacy SoC camera drivers will be moving to staging, as they're
outdated and nobody so far is willing to fix and convert them to use
the current media framework
- As usual, lots of cleanups, improvements and new board additions.
* tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (381 commits)
media: au0828 disable tuner to demod link in au0828_media_device_register()
[media] touptek: cast char types on %x printk
[media] touptek: don't DMA at the stack
[media] mceusb: use %*ph for small buffer dumps
[media] v4l: exynos4-is: Drop unneeded check when setting up fimc-lite links
[media] v4l: vsp1: Check if an entity is a subdev with the right function
[media] hide unused functions for !MEDIA_CONTROLLER
[media] em28xx: fix Terratec Grabby AC97 codec detection
[media] media: add prefixes to interface types
[media] media: rc: nuvoton: switch attribute wakeup_data to text
[media] v4l2-ioctl: fix YUV422P pixel format description
[media] media: fix null pointer dereference in v4l_vb2q_enable_media_source()
[media] v4l2-mc.h: fix yet more compiler errors
[media] staging/media: add missing TODO files
[media] media.h: always start with 1 for the audio entities
[media] sound/usb: Use meaninful names for goto labels
[media] v4l2-mc.h: fix compiler warnings
[media] media: au0828 audio mixer isn't connected to decoder
[media] sound/usb: Use Media Controller API to share media resources
[media] dw2102: add support for TeVii S662
...
1/ Asynchronous address range scrub:
Given the capacities of next generation persistent memory devices a
scrub operation to find all poison may take 10s of seconds. We want
this scrub work to be done asynchronously with the rest of system
initialization, so we move it out of line from the NFIT probing, i.e.
acpi_nfit_add().
2/ Clear poison:
ACPI 6.1 introduces the ability to send "clear error" commands to the
ACPI0012:00 device representing the root of an "nvdimm bus". Similar to
relocating a bad block on a disk, this support clears media errors in
response to a write.
3/ Persistent memory resource tracking:
A persistent memory range may be designated as simply "reserved" by
platform firmware in the efi/e820 memory map. Later when the NFIT
driver loads it discovers that the range is "Persistent Memory". The
NFIT bus driver inserts a resource to advertise that "persistent"
attribute in the system resource tree for /proc/iomem and
kernel-internal usages.
4/ Miscellaneous cleanups and fixes:
Workaround section misaligned pmem ranges when allocating a struct page
memmap, fix handling of the read-only case in the ioctl path, and clean
up block device major number allocation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=F67V
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Asynchronous address range scrub:
Given the capacities of next generation persistent memory devices a
scrub operation to find all poison may take 10s of seconds. We
want this scrub work to be done asynchronously with the rest of
system initialization, so we move it out of line from the NFIT
probing, i.e. acpi_nfit_add().
- Clear poison:
ACPI 6.1 introduces the ability to send "clear error" commands to
the ACPI0012:00 device representing the root of an "nvdimm bus".
Similar to relocating a bad block on a disk, this support clears
media errors in response to a write.
- Persistent memory resource tracking:
A persistent memory range may be designated as simply "reserved" by
platform firmware in the efi/e820 memory map. Later when the NFIT
driver loads it discovers that the range is "Persistent Memory".
The NFIT bus driver inserts a resource to advertise that
"persistent" attribute in the system resource tree for /proc/iomem
and kernel-internal usages.
- Miscellaneous cleanups and fixes:
Workaround section misaligned pmem ranges when allocating a struct
page memmap, fix handling of the read-only case in the ioctl path,
and clean up block device major number allocation.
* tag 'libnvdimm-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (26 commits)
libnvdimm, pmem: clear poison on write
libnvdimm, pmem: fix kmap_atomic() leak in error path
nvdimm/btt: don't allocate unused major device number
nvdimm/blk: don't allocate unused major device number
pmem: don't allocate unused major device number
ACPI: Change NFIT driver to insert new resource
resource: Export insert_resource and remove_resource
resource: Add remove_resource interface
resource: Change __request_region to inherit from immediate parent
libnvdimm, pmem: fix ia64 build, use PHYS_PFN
nfit, libnvdimm: clear poison command support
libnvdimm, pfn: 'resource'-address and 'size' attributes for pfn devices
libnvdimm, pmem: adjust for section collisions with 'System RAM'
libnvdimm, pmem: fix 'pfn' support for section-misaligned namespaces
libnvdimm: Fix security issue with DSM IOCTL.
libnvdimm: Clean-up access mode check.
tools/testing/nvdimm: expand ars unit testing
nfit: disable userspace initiated ars during scrub
nfit: scrub and register regions in a workqueue
nfit, libnvdimm: async region scrub workqueue
...
(dm-mq) that is used exclussively by DM multipath.
- A stable fix for dm-mq that eliminates excessive context switching
offers the biggest performance improvement (for both IOPs and
throughput).
- But more work is needed, during the next cycle, to reduce spinlock
contention in DM multipath on large NUMA systems.
- A stable fix for a NULL pointer seen when DM stats is enabled on a DM
multipath device that must requeue an IO due to path failure.
- A stable fix for DM snapshot to disallow the COW and origin devices
from being identical. This amounts to graceful failure in the face of
userspace error because these devices shouldn't ever be identical.
- Stable fixes for DM cache and DM thin provisioning to address crashes
seen if/when their respective metadata device experiences failures
that cause the transition to 'fail_io' mode.
- The DM cache 'mq' policy is now an alias for the 'smq' policy. The
'smq' policy proved to be consistently better than 'mq'. As such
'mq', with all its complex user-facing tunables, has been eliminated.
- Improve DM thin provisioning to consistently return -ENOSPC once the
thin-pool's data volume is out of space.
- Improve DM core to properly handle error propagation if
bio_integrity_clone() fails in clone_bio().
- Other small cleanups and improvements to DM core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW6WRhAAoJEMUj8QotnQNaXiIH/3UBJ0w/YUrAOcTU9Q58FQoo
JophkKbjZ7o9IUNdDmfv9vQSFAJvDOJ8ve2Sb5OXdW0mUWxM+8M+6ioQU4MtI9oN
uBZ7MDYU995jzE89d8sYFO9lKrNCmmPKuBiIzoAGNVh1VPx8YK1PvTOfaGEk5VHg
Ay5JYGn14PUuV9tOP4euvpuc4XrJn5lqWtnTeMZPLtytcO3LWDIFGDoPoUqoRLI3
yzBO08xzR/xTNiW4+f59U7AJE+80CAONld0EDPRhrbd9kl3d1EcyCULisBQzuVd3
VSL0t77x4tPLWFR7Z1Fsq1FamuwSAUYL1FLLusT6G+5LUXdv0TAm+kXiUDA1Tbc=
=1SLF
-----END PGP SIGNATURE-----
Merge tag 'dm-4.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Most attention this cycle went to optimizing blk-mq request-based DM
(dm-mq) that is used exclussively by DM multipath:
- A stable fix for dm-mq that eliminates excessive context
switching offers the biggest performance improvement (for both
IOPs and throughput).
- But more work is needed, during the next cycle, to reduce
spinlock contention in DM multipath on large NUMA systems.
- A stable fix for a NULL pointer seen when DM stats is enabled on a DM
multipath device that must requeue an IO due to path failure.
- A stable fix for DM snapshot to disallow the COW and origin devices
from being identical. This amounts to graceful failure in the face
of userspace error because these devices shouldn't ever be identical.
- Stable fixes for DM cache and DM thin provisioning to address crashes
seen if/when their respective metadata device experiences failures
that cause the transition to 'fail_io' mode.
- The DM cache 'mq' policy is now an alias for the 'smq' policy. The
'smq' policy proved to be consistently better than 'mq'. As such
'mq', with all its complex user-facing tunables, has been eliminated.
- Improve DM thin provisioning to consistently return -ENOSPC once the
thin-pool's data volume is out of space.
- Improve DM core to properly handle error propagation if
bio_integrity_clone() fails in clone_bio().
- Other small cleanups and improvements to DM core.
* tag 'dm-4.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (41 commits)
dm: fix rq_end_stats() NULL pointer in dm_requeue_original_request()
dm thin: consistently return -ENOSPC if pool has run out of data space
dm cache: bump the target version
dm cache: make sure every metadata function checks fail_io
dm: add missing newline between DM_DEBUG_BLOCK_STACK_TRACING and DM_BUFIO
dm cache policy smq: clarify that mq registration failure was for 'mq'
dm: return error if bio_integrity_clone() fails in clone_bio()
dm thin metadata: don't issue prefetches if a transaction abort has failed
dm snapshot: disallow the COW and origin devices from being identical
dm cache: make the 'mq' policy an alias for 'smq'
dm: drop unnecessary assignment of md->queue
dm: reorder 'struct mapped_device' members to fix alignment and holes
dm: remove dummy definition of 'struct dm_table'
dm: add 'dm_numa_node' module parameter
dm thin metadata: remove needless newline from subtree_dec() DMERR message
dm mpath: cleanup reinstate_path() et al based on code review
dm mpath: remove __pgpath_busy forward declaration, rename to pgpath_busy
dm mpath: switch from 'unsigned' to 'bool' for flags where appropriate
dm round robin: use percpu 'repeat_count' and 'current_path'
dm path selector: remove 'repeat_count' return from .select_path hook
...
This pull includes driver updates from the usual suspects (stex, hpsa,
ncr5380, scsi_dh, qla2xxx, be2iscsi, hisi_sas, cxlflash, aacraid,
mp3sas, megaraid_sas, ibmvscsi, ufs) plus an assortment of
miscellaneous fixes. The major user visible change of this pull is
that we've moved from monotonically increasing host number to an ida
allocated one (meaning the numbers get re-used) because someone
managed to wrap the count in an iscsi system. We don't believe there
will be any adverse consequences of this.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJW6I3XAAoJEDeqqVYsXL0MyHoH+wWPbgLhMwjLL2KXwOrx73i7
HF3JttnYCbOGHlAz01mGnOdQF2bD9EqChQk1blsu0lVX0agbZ20CbXiEhwM4Iphn
45fIKpVbTSEfTQOnPHs8gcVx6ToidHkpQ224wB9LPtkrQtEldmmPlqBNvpEg8m1s
382YPZ7Nn1p9Ci92L9RpztHuC9luUnfndOAgIrtEWBKWkIPeSaJ9iElY5bOf+gJ/
t8ft3SGcljj1i73z0LNEvoQyggUb0yEW9iyi72Cmn2DeGnKbKOWlP1oV77aq3MuO
8TYxG6qaUn1zOoZDwOnl25MpT7FWuG1RvBcoCrOTPuoXGVgk9MAJi5w+YG/5LFk=
=xX0G
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This pull includes driver updates from the usual suspects (stex, hpsa,
ncr5380, scsi_dh, qla2xxx, be2iscsi, hisi_sas, cxlflash, aacraid,
mp3sas, megaraid_sas, ibmvscsi, ufs) plus an assortment of
miscellaneous fixes.
The major user visible change of this pull is that we've moved from
monotonically increasing host number to an ida allocated one (meaning
the numbers get re-used) because someone managed to wrap the count in
an iscsi system. We don't believe there will be any adverse
consequences of this"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (230 commits)
MAINTAINERS: use new email address for James Bottomley
mpt3sas: Remove unnecessary synchronize_irq() before free_irq()
sg: fix dxferp in from_to case
cxlflash: Increase cmd_per_lun for better throughput
cxlflash: Fix to avoid unnecessary scan with internal LUNs
cxlflash: Reorder user context initialization
cxlflash: Simplify attach path error cleanup
cxlflash: Split out context initialization
cxlflash: Unmap problem state area before detaching master context
cxlflash: Simplify PCI registration
scsi: storvsc: fix SRB_STATUS_ABORTED handling
be2iscsi: set the boot_kset pointer to NULL in case of failure
sd: Fix discard granularity when LBPRZ=1
be2iscsi: Remove unnecessary synchronize_irq() before free_irq()
scsi_sysfs: call 'device_add' after attaching device handler
scsi_dh_emc: update 'access_state' field
scsi_dh_rdac: update 'access_state' field
scsi_dh_alua: update 'access_state' field
scsi_dh_alua: use common definitions for ALUA state
scsi: Add 'access_state' and 'preferred_path' attribute
...
Pull iscsi_ibft update from Konrad Rzeszutek Wilk:
"A simple patch that had been rattling around in SuSE repo"
* 'stable/for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft:
iscsi_ibft: Add prefix-len attr and display netmask
David Daney says:
====================
net/phy: Fixes for Cavium Thunder MDIO code.
Previous patch set:
commit 5fc7cf1794 ("net: thunderx: Cleanup PHY probing code.")
commit 1eefee901f ("phy: mdio-octeon: Refactor into two files/modules")
commit 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Had several problems. We try to fix them here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible, although unlikely, that probing will find the
phy_device for the first LMAC of a thunder BGX device, but then need
to fail with -EPROBE_DEFER on a subsequent LMAC. In this case, we
need to call put_device() on each of the phy_devices that were
obtained, but will be unused due to returning -EPROBE_DEFER.
Also, since we can break out of the probing loop early, we need to
explicitly call of_node_put() outside of the loop.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we selected MDIO_OCTEON, which after creating the Thunder
specific MDIO bus driver is much less useful.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the code was factored out of mdio-octeon.c, the
MODULE_DESCRIPTION, MODULE_AUTHOR and MODULE_LICENSE annotations were
inadvertently omitted. Restore them so that we don't get kernel taint
warnings upon module loading.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking ppp_mutex must be done before dereferencing file->private_data,
otherwise it could be modified before ppp_unattached_ioctl() takes the
lock. This could lead ppp_unattached_ioctl() to override ->private_data,
thus leaking reference to the ppp_file previously pointed to.
v2: lock all ppp_ioctl() instead of just checking private_data in
ppp_unattached_ioctl(), to avoid ambiguous behaviour.
Fixes: f3ff8a4d80 ("ppp: push BKL down into the driver")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caesar Wang says:
====================
arc_emac: fixes the emac issues and cleanup emac drivers
This series patches are based on kernel 4.5-rc7+ version.
Linux version 4.5.0-rc7-next-20160311+ (wxt@nb) (...) #45 SMP Sun Mar 13 16:17:56
The history patch in here:
Patch-v1: https://lkml.org/lkml/2016/3/11/209
Patch-v2: https://lkml.org/lkml/2016/3/13/39
Verified on kylin board with my github.
https://github.com/Caesar-github/rockchip/tree/kylin/next
That's verified on kylin board with ubuntu os.
This series patches are built all pass with Mr.robot on
https://github.com/Caesar-github/linux/tree/build-emac-v3
How to test and verify?
You can refer to the following wiki document.
http://rockchip.wikidot.com/linux-develop-guide
bootup log:
[ 1.264740] rockchip_emac 10200000.ethernet: no regulator found
[ 1.270908] rockchip_emac 10200000.ethernet: ARC EMAC detected with id: 0x7fd02
[ 1.278362] rockchip_emac 10200000.ethernet: IRQ is 29
[ 1.283747] rockchip_emac 10200000.ethernet: MAC address is now 06:5d:61:c7:39:41
[ 1.291314] rockchip_emac 10200000.ethernet: GPIO lookup for consumer phy-reset
[ 1.291333] rockchip_emac 10200000.ethernet: using device tree for GPIO lookup
[ 1.663155] rockchip_emac 10200000.ethernet: connected to Generic PHY phy with id 0xffffc816
[ 8.863448] rockchip_emac 10200000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
root@localhost:/# busybox ping www.baidu.com
PING www.baidu.com (14.215.177.38): 56 data bytes
64 bytes from 14.215.177.38: seq=0 ttl=48 time=35.046 ms
64 bytes from 14.215.177.38: seq=1 ttl=48 time=35.095 ms
64 bytes from 14.215.177.38: seq=2 ttl=48 time=34.203 ms
64 bytes from 14.215.177.38: seq=3 ttl=48 time=38.516 ms
...
---
1) This series has 6 patches: (1--->9)
net: arc_emac: make the rockchip emac document more compatible
net: arc_emac: add phy reset is optional for device tree
net: arc_emac: support the phy reset for emac driver
net: arc: trivial: cleanup the emac driver
clk: rockchip: add node-id for rk3036 emac hclk
clk: rockchip: associate the rk3036 HCLK_EMAC clock-id
clk: rockchip: add clock-id for rk3036 emac pll source clock
clk: rockchip: associate SCLK_MAC_PLL and disable reparenting on rk3036
ARM: dts: rockchip: add support emac for RK3036
2) This series patches have the following descriptions:
Hi Rob, David:
PATCH[1/9-2/9]: ====>
net: arc_emac: make the rockchip emac document more compatible
net: arc_emac: add phy reset is optional for device tree
The patches change the rockchip emac document for more compatible and
Add the phy reset property for document.
---
Hi David
PATCH[3/9]: ====>
net: arc_emac: support the phy reset for emac driver
The emac didn't work on kylin board since in some case the clocks parent changed.
The kylin hardware connects the phy reset pin, we should use it with real world.
As the previous patch discuss on https://patchwork.kernel.org/patch/8186801/
And as sergei/Heiko suggestions on
https://patchwork.kernel.org/patch/8564571/
---
Hi David
PATCH[4/9]: ====>
net: arc: trivial: cleanup the emac driver
The first time to look the emac drivers, I think that have to cleanup the drivers with scripts.
Although it's the trivial things, in order to be more read.
---
Hi Heiko,Michael,Stephen:
PATCH[5/9-8/9]: ====> clk: rockchip: rk3036: fix and add node id for emac clock
Four-part from https://patchwork.kernel.org/patch/8564581/
clk: rockchip: add node-id for rk3036 emac hclk
clk: rockchip: associate the rk3036 HCLK_EMAC clock-id
clk: rockchip: add clock-id for rk3036 emac pll source clock
clk: rockchip: associate SCLK_MAC_PLL and disable reparenting on rk3036
Add the emac needed clocks for rk3036 SoCs
---
Hi Heiko:
PATCH[9/9]: ====>
ARM: dts: rockchip: add support emac for RK3036
Add the emac needed main info for rk3036 dts.
---
Thanks your reviewing! :)
Changes in v3:
- %s/he/the
- Add the Cc people
- As Sergei comments, the original name is better, so
%s/reset-gpios/phy-reset-gpios
- Add the Cc people.
- Caused the build error since the missing include head file.
- %s/reset/phy-reset to match the device tree.
- Add the Cc people
- Add the Cc people.
- Add the Cc people.
- Add the Cc people.
- Add the Cc people.
- Add the Cc people.
- rename reset-gpio to phy-reset-gpios.
- change the commit.
- remove the pcfg_output_high, that's really not needed for emac.
- Add the Cc people.
- Fixes the 'zhengxing' to 'Xing Zheng'.
Changes in v2:
- change the commit and remove the repeat the name 'rockchip'.
- %s/phy-reset-gpios/reset-gpios
- As the pervious version, Sergei and Heiko comments on
https://patchwork.kernel.org/patch/8564571/.
- Nevermind, add signed-off since Heiko the original patch,
refer the Heiko's test patch on
a943c58878
:)
- As the robot notice the build error since overflow in implicit
constant conversion.
- rename phy-reset-gpio to reset-gpios.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the emac device node for rk3036 SoCs.
We need to let mac clock under the DPLL which is able to provide
the accurate 50MHz what mac_ref need, since that will cause some
unstable things if the cpufreq is working.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: linux-rockchip@lists.infradead.org
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The emac needs constant and very specific rate but the possible PLL-sources
are very limited, so we expect the PLL source to be set manually on per
board and don't want it to get changed in an automatic way later.
So add the necessary clock-id and disable reparenting on set_rate calls.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suitable PLLs for the emac on the rk3036 are difficult to find
and one of them is the (continuously changing) APLL. So in most
cases it will be necessary to select a PLL manually.
So add a clock-id for it.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Associate the new clock id the clock.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the node-id for the emac hclk to the binding header.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will make the driver more readability
The emac has the error and warnings if you run
'scripts/checkpatch.pl -f --subjective xxx' to check.
Let's clean up such trivial details.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to support the emac phy reset.
Different boards may require different phy reset duration. Add property
phy-reset-duration for emac driver, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following property for arc_emac.
1) phy-reset-gpios:
The phy-reset-gpio is an optional property for arc emac device tree boot.
Change the binding document to match the driver code.
2) phy-reset-duration:
Different boards may require different phy reset duration. Add property
phy-reset-duration for device tree probe, so that the boards that need
a longer reset duration can specify it in their device tree.
Anyway, we can add the above property for arc emac.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc; Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the rk3036 SoCs to match driver for document since the emac driver
has supported the rk3036 SoCs.
This patch adds the rk3036/rk3066/rk3188 SoCS to compatible for rockchip
emac ducument. Also, that will suit for other SoCs in the future.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ETHTOOL_GLINKSETTINGS implementation finds that userland is
using the wrong number of words of link mode bitmaps (or is trying to
find out the right numbers) it sets the cmd field to 0 in the response
structure.
This is inconsistent with the implementation of every other ethtool
command, so let's remove that inconsistency before it gets into a
stable release.
Fixes: 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
